VULCAN 16™
Powder Coating Oven

Choose an oven that fits your largest regular part with a few inches of clearance. The Vulcan 16's 30" x 30" x 30" chamber fits wheels up to 28" and batches of brackets and small parts.

Most powders cure at around 350°F to 400°F. The Vulcan 16 reaches 400°F in about 15 minutes and goes up to 475°F.

You can for small parts, but never use that oven for food again, because curing powder releases fumes. A kitchen oven also holds temperature less evenly, about ±20°F compared with ±5°F in the Vulcan 16.

Yes. Clean and blast the aluminum, then outgas cast aluminum by preheating it above the cure temperature before you spray, so trapped gas doesn't bubble the finish.

The Vulcan 16 needs a 240V single-phase circuit with a 25A fused supply. Have an electrician check your panel before you install it.

Vulcan 16 ships unassembled via FedEx Ground in three separate boxes weighing approximately 125lbs each.

Some units may be shipped via LTL freight depending on factors such as size, weight, packaging requirements, or logistical considerations.

If you plan to powder coat small or lightweight parts, you can likely get creative with your own fixture. If you want to get powder coating as quickly and efficiently as possible with part scalability, we recommend purchasing our fixtures.

Vulcan 16 is designed for precise thermal control of +/- 5 °F throughout the entire 16 cubic foot cure volume. A home appliance oven typically maintains +/- 20 °F across the normal 5 cubic feet.

Until now, powder coat ovens have been offered by our competitors using galvanized steel, which is toxic at temperatures required for powder curing. Langmuir Systems prioritizes your safety with stainless steel interiors so you can powder coat without the worry of long-term health risk.

CureControl is our in-house software for Vulcan 16. Our software maximizes your efficiency as a hobbyist or small business owner to its fullest potential through the use of custom cure profiles and a built-in Time-To-Temp calculator. Making batch production runs is no problem for Vulcan 16 as it saves your parts and cure times into its memory so that you can add a signature finish at the touch of a button without the hassle of temperature monitoring.

Vulcan 16 is a tier above the competition. Langmuir Systems offers the best materials, insulation, and productivity that money can buy at no additional cost to the user. By design, we have maximized the curing volume to fit up to 28” wheel rims all while maintaining a temperature rise time of 15 minutes or less.

No, we do not currently supply powder finishes, but online retailers such as Prismatic Powders and Powder Buy The Pound offer hundreds of color variants.

Powder coat finishes are much more durable than paint and resist damage much more effectively with fewer coats. Additionally, powder overspray can be recollected and used as opposed to any lost paint with aerosol-based paints.

Vulcan 16 is engineered to the maximum possible size with the electronic components provided because the team at Langmuir understand that sometimes, bigger IS better. While we may offer a larger curing oven in the future, it is not currently in development.

Yes. Add Vulcan 16 Assembly ($400) when you order, and we'll fully assemble your oven for local pickup or freight shipping from Conroe, TX.

As with all new tools, we recommend becoming familiar with the machine and processes for getting the results you want. To get started, we have provided a comprehensive suite of videos, assembly guides, and general knowledge to get you up and running located in the support tab at the top of the page. For any other questions, email [email protected].

Vulcan 16 ships standard with two-inch thick, fireproof mineral wool insulation rated for 1200 °F for the best performance.

All products sold directly by Langmuir Systems are eligible for return and refund. The terms of the return and refund policy are listed below:

1. Only the original buyer of the item is eligible to return the item for a refund. Proof of purchase is required in order to be eligible for a refund.
2. A return must be requested within 30 calendar days following the delivery of the item. Return requests after the eligibility period will be denied.
3. The buyer is responsible for all shipping and handling costs associated with shipping the item back.
4. Items that are eligible for return must meet all of the following requirements:
   The item must be in unused condition.
   The item must be free of defects.
   The item must be received in the original packaging.
5. Langmuir Systems will inspect the item within 5 business days of receiving it. The buyer will be informed if it passes inspection and thus is eligible for a refund.
6. If Langmuir Systems concludes that the item meets the refund eligibility requirements, a refund for the original transaction amount minus a 20% restocking fee will be issued to the Buyer within 5 business days following the completion of the inspection.
7. 'In person' returns require permission from Langmuir Systems in advance.

Please see our Warranty, Refund, and Return Policy for full details on warranties, returns, and refunds.